(f)air tightness® GREY Airtightness Tape
(f)air tightness GREY is a vapour-permeable adhesive fleece tape designed for airtight and windtight sealing of membrane overlaps, joints and suitable connections in the building envelope.
The tape is suitable for internal and external applications. Its non-woven polypropylene carrier provides a surface that can be painted or plastered over, subject to appropriate preparation and finishing conditions.
GREY uses an acrylic dispersion adhesive and bonds to a range of suitable construction substrates, including airtightness and vapour control membranes, breathable membranes, PE films, uPVC, metal, timber, plywood and OSB. Some substrates may require primer treatment.
PRODUCT BENEFITS
- Vapour-permeable fleece tape for airtight and windtight connections.
- Suitable for internal and external applications.
- Non-woven polypropylene carrier can be painted or plastered over, subject to finishing requirements.
- Compatible with a wide range of suitable construction membranes and substrates.
- Durable airtight bonding performance tested according to DIN 4108-11.
- Peel adhesion of 26 N/25 mm according to the technical data sheet.
- UV resistance of up to 4 months as stated in the technical data sheet.
- Available in 50 mm and 60 mm widths, supplied in 25 m rolls.
- Practical for suitable construction connections where a fleece-faced surface is required.
APPLICATIONS & INSTALLATION GUIDANCE
Applications
(f)air tightness GREY is intended for airtight and windtight sealing applications in suitable wall, ceiling, roof and building envelope constructions.
Typical applications include sealing overlaps between airtightness membranes, vapour control layers and breathable membranes, as well as suitable connections to construction boards and other compatible substrates.
Its non-woven fleece carrier makes GREY particularly useful for connections where the tape surface is intended to be painted or covered with plaster. The suitability of the complete joint and the finishing material must be verified for the intended application.
Surface Preparation
- Ensure bonding surfaces are clean, dry, stable and free from dust, grease, frost and loose particles.
- Remove contamination that could reduce adhesive performance.
- Check the condition and compatibility of each substrate before application.
- Some porous, dusty or difficult substrates may require a suitable primer.
- Carry out an adhesion test where substrate suitability is uncertain.
Sealing Membrane Overlaps
- Arrange membrane overlaps to allow continuous and reliable adhesive sealing.
- Ensure that the underlying membrane and joint are adequately supported.
- Apply GREY tape centrally across the overlap wherever practical.
- Lay the tape smoothly without unnecessary tension, folds or wrinkles.
- Avoid trapped air and unsupported adhesive joints.
- Press the tape firmly over its entire bonded surface using a suitable application roller.
- Inspect completed joints and repair discontinuities to maintain airtightness.
Connections to Other Building Materials
- GREY may be used for suitable connections to compatible uPVC, metal, timber, plywood and OSB surfaces.
- Evaluate adhesion to each substrate and use primer where required.
- Provide adequate support where joints could otherwise be exposed to mechanical stress.
- Allow for movement between adjacent construction elements where necessary.
- Avoid continuous peeling loads on the adhesive bond.
Painting and Plastering
The non-woven carrier can be painted or plastered over according to the technical data sheet. Compatibility with the selected coating or plaster system should be verified before finishing.
To reduce the risk of cracking, the technical data sheet advises that the tape should not cover a substrate area of 60 mm width. The connection detail, tape positioning and intended plaster or paint finish must therefore be considered together.
External Applications and UV Exposure
The technical data sheet specifies UV resistance of up to 4 months. This does not establish that every taped joint is permanently weatherproof or suitable for unrestricted outdoor exposure.
External applications must account for water management, substrate compatibility, movement and the intended exposure conditions.
Application During Cold Weather
The specified processing temperature range is -10°C to +35°C. Applications below +5°C require particular care to ensure reliable adhesion.
- Do not apply the tape to wet, icy or frozen substrates.
- Check substrate condition and suitability before bonding.
- Condition cold materials where necessary and practical.
- Press the tape firmly and check initial adhesion.
- Carry out adhesion tests under challenging site conditions.
Storage and Handling
Store the tape in its original packaging under dry conditions at +15°C to +25°C. The technical data sheet specifies a relative humidity range of 40% to 60% for storage.
Protect rolls against contamination, excessive temperatures and mechanical damage.
Health, Safety and Disposal
Use appropriate cutting tools and follow normal construction-site safety practices. Dispose of packaging and waste materials in accordance with applicable local regulations.
General Installation Note
The suitability of the adhesive tape depends on the substrate, surface preparation, joint design and application conditions. Verify compatibility with any intended paint or plaster finish and carry out adhesion tests where required. Protect the completed airtightness system against subsequent damage.
TECHNICAL DATA
| Property | Value |
|---|---|
| Product type | Vapour-permeable airtightness & windtightness tape |
| Intended use | Internal and external applications |
| Carrier material | Non-woven PP |
| Adhesive | Acrylic dispersion |
| Colour | Grey |
| Roll dimensions | 50 mm / 60 mm × 25 m |
| Durable airtight bonding | Passed – DIN 4108-11 |
| Reaction to fire | Class E – DIN EN 13501-1 |
| UV resistance | Maximum 4 months |
| GEV EMICODE | Not available (n.a. in TDS) |
| Peel adhesion | 26 N/25 mm |
| Elongation | 40% |
| Processing temperature | −10°C to +35°C* |
| Temperature resistance | −40°C to +100°C |
| Storage temperature | +15°C to +25°C |
| Storage relative humidity | 40–60% |
| Resistance to condensation | High |
| Surface finish | Paintable / plasterable, subject to compatibility |
*Processing temperatures below +5°C require special care during application.